Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Pasadena
Gate parts and welding in Pasadena usually come down to one of three jobs: a hinge that has pulled loose, a post that has shifted or rotted, or a rail that has split and needs a weld. On most Pasadena properties we can handle that same day, and we quote the price before any work starts so you are never surprised at the door. Hal Gatewood has been owner-operating this company since 2001, and the person who answers your call is the person who shows up. For a free estimate on hinge replacement, post work, rail repair, or custom welding, call (626) 628-9548.
Why Gatewood Fence & Gate Is Pasadena’s Preferred Gate Parts & Welding Company
Most of our Pasadena work comes from referrals, and that is the way we like it. A neighbor on Marengo Avenue watches us reset a leaning post on a 1930s Spanish Colonial, then calls us when their own driveway gate starts dragging. We have been serving Pasadena long enough to know which blocks have original 1920s footings and which newer builds can take a prefab hinge without issue. Hal’s name is on the shop and on every invoice, and the shop is down the road, not three states away.
Every job carries the 90-Day Done Right Promise in writing. If something is not right, one call brings Hal back. No runaround, no phone tree. We also answer the phone with a live person 24 hours a day, 7 days a week, because a gate that will not close at 10pm in Pasadena is a security problem, not an inconvenience. Our Pasadena customers consistently tell us the same thing: the person who did the work is the person they can look in the eye at the hardware store a week later.
Our Gate Parts & Welding Services in Pasadena
We do the work in your driveway whenever the gate can stay in place. That matters on older Pasadena gates, where removing the gate means hauling a 90-year-old redwood panel that may not survive the trip. Here are the four jobs we handle most often, and how they show up on Pasadena properties.
Hinge Replacement
Pasadena’s Craftsman-era gates often hang on original strap hinges that have been in service since the Coolidge administration. When those pull loose from a spalled post, the gate sags and the latch stops lining up. We remove the old hardware, repair or shim the post, and set new hinges sized to the actual gate weight, not whatever was on the shelf. On historic properties we can weld period-appropriate hinge profiles so the fix does not shout at the house.
Post Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. In Pasadena, original post footings were often poured between 1920 and 1940, and many have shifted or spalled. We dig out the old footing, set a new concrete base, and reset or replace the post so it carries the gate instead of leaning with it. Fix the panel without the post and you will fix it twice.
Rail Repair
Wide temperature swings between Pasadena mornings and afternoons work wooden rails hard. Redwood and cedar expand and contract enough to split rails and pop screws, especially on unshaded south-facing gates. We weld split rails back together with steel reinforcement plates where the frame allows, and we tell you honestly when the wood is too far gone to hold a repair. A welded steel brace on a solid rail lasts decades; a weld on punky wood is a waste of your money.
Custom Welding
Some Pasadena gates need a part that has not been manufactured in fifty years. We fabricate on site: custom hinge plates, latch extensions, steel gate rollers, frame reinforcements, and replacement iron pickets matched to the existing work. Hal welds in your driveway, which means you can watch the work happen and see exactly what you are paying for.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Pasadena
For automated gates, we stock parts and service operators from FAAC, Linear, and Viking, plus most other major brands on the market. The older the operator, the more likely the control board is obsolete, and that is a conversation we have often in Pasadena. We tell you straight when a board can be rebuilt or a diode replaced, and when you are better off putting that money toward a new operator with current safety edges. No upsell, just the honest arithmetic. On a legacy gate with a dead board, we can often get you running again with a retrofitted aftermarket control rather than replacing the entire drive.
Common Gate Parts & Welding Problems We See in Pasadena Homes
- Original 1920s-1940s concrete footings that have shifted or spalled. This is the single most common cause of sagging gates in Pasadena’s older neighborhoods. The hinge post leans, the top hinge pulls, and the gate drags worse every season until someone resets the footing.
- Santa Ana wind damage to wooden hinge posts. Pasadena sits directly against the San Gabriel Mountain front, which amplifies Santa Ana gusts. We routinely see top hinges snapped under wind load on gates that would never fail in a coastal city.
- Split rails on Craftsman-era redwood and cedar gates. The wide diurnal temperature swing between Pasadena’s cool mornings and hot afternoons accelerates expansion and contraction. Unshaded gates split rails and pop screws far more often here than they do in flatland cities.
- Obsolete operator control boards on legacy automatic gates. A 2003 LiftMaster swing operator on an Orange Grove Boulevard estate may have a control board that is no longer made. We can often retrofit a current aftermarket board and keep the original motor, rather than swapping the entire drive.
Pricing for Gate Parts & Welding in Pasadena, CA
Here are the ranges we quote on most Pasadena jobs. A hinge replacement on a wooden driveway gate typically runs $180-$340, depending on whether the post needs shimming or repair. Post replacement with a new concrete footing starts around $450-$800 for a standard 4×4 gate post, and goes up from there for 6×6 or steel posts. Rail repair with welding runs $150-$350, depending on the length of the split and whether we are adding steel reinforcement. Custom welding work is quoted per job after Hal looks at the gate, and the quote always comes before any work starts. We also offer $40 off any repair over $200, a free second opinion on any written estimate, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (626) 628-9548 and we will give you the number before we touch a tool.
We Also Serve Cities Near Pasadena
Our crews work Pasadena regularly, and we also cover Pasadena-adjacent communities including San Marino, Altadena, San Gabriel, and Alhambra. If you are in one of those cities, the trip charge is the same: zero, inside the county. Call and ask for Hal.
Serving Pasadena, CA - Our Local Coverage Area
We’re based in the Pasadena area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Pasadena
If your home is a contributing structure inside the Bungalow Heaven Landmark District, you may need a Certificate of Appropriateness before altering gate hardware or replacing a gate that is visible from the street. This is not optional if the city considers the gate part of the historic fabric. The good news: we have done this enough times to know what the Historic Preservation Commission looks for, and we can help you prepare the application with period-appropriate hardware specifications. Call (626) 628-9548 and we will walk you through it.
Pasadena’s original 1920s-to-1940s concrete footings were often poured shallow and without steel reinforcement, and many have spalled or shifted over nine decades. Temple City tends to be newer construction with deeper, reinforced footings that hold up better. Add Pasadena’s amplified Santa Ana winds channeling against the mountain front, and you get leaning posts that flatland cities rarely see.
We can weld original wrought iron, provided the metal is still sound. Wrought iron is low-carbon and welds well, but we inspect for hidden cracks and fatigue first. If the hinge is beyond saving, we can fabricate a replacement that matches the original profile and finish, so the gate looks right from the street and still carries its weight.
Usually not. A sagging hinge post makes the operator work harder and can burn out limit switches, but the operator itself often still has life in it. We reset the post first, realign the gate, then test the operator under its new load. Changing the operator before fixing the post is putting a new engine in a car with a bent axle. Call (626) 628-9548 and we will diagnose it properly.
Welding a steel reinforcement plate across a split rail usually costs $150-$350, versus $900-$1,800 to rebuild a Craftsman-style redwood panel in Pasadena. If the surrounding wood is solid, welding is the clear win. If the wood is soft or the split runs through a joint, we will tell you before we quote the weld, because a repair on compromised wood will fail and cost you twice.
Call Gatewood Fence & Gate for Gate Parts & Welding in Pasadena
If your gate is sagging, dragging, or hanging by one hinge, call (626) 628-9548 for a free estimate. Hal will answer or call you back fast, and he will give you the price before any work starts. We have been owner-operated since 2001, and the name on the shop is the name on the invoice. For Gate Parts & Welding in Pasadena, you will get a straight answer and a fix that holds.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Pasadena since 2001.