Ghost Controls Gate Installation Nationwide | Gatewood Fence & Gate

Ghost Controls Gate Installation in Arcadia: What to Know First

Ghost Controls gate installation in Arcadia typically runs from $450 to $1,200 for the opener and hardware on an existing gate, while a full gate-and-opener package usually lands between $2,800 and $6,500 depending on gate size, material, and whether we’re dealing with a single swing, double swing, or slide setup. We’re an independent Ghost Controls service provider, not a factory outfit, so we quote the job after looking at your driveway, not from a script. Most Ghost Controls installations in Arcadia take one full day, sometimes two when the gate itself needs steel work or hinge replacement. If you already own the opener and need it mounted, wired, and dialed in, call us at (626) 628-9548 and we’ll tell you straight what it’ll take.

Call (626) 628-9548

This page is for Arcadia homeowners who bought a Ghost Controls kit or opener and hit the wall every DIYer eventually hits: the post isn’t plumb, the gate sags a half-inch more than the manual says is acceptable, or the opener runs fine for three days and then throws a fault code nobody at the big-box store can explain. “Tell me what it is doing and I will tell you what it needs - no runaround.” That’s how we work at Gatewood Fence & Gate, and it’s been that way since Hal Gatewood started the outfit in 2001.

How Ghost Controls Products Fail - and How We Fix Them

We open a lot of Ghost Controls panels in Arcadia, and the failures we see are rarely the opener’s fault. The opener is usually trying to do its job while the gate fights it. Here’s what we actually find:

• Phantom power loss and the “dead keypad” on the TSS and RVS series. Most times the opener hasn’t failed. The inline fuse holder or the wiring going through a sagging gate hinge has. We’ve seen Arcadia homes where the original installer ran low-voltage wire through the hinge line without a drip loop, and after two winters of rain the wire corroded inside the insulation. The fix isn’t a new opener; it’s a proper weatherproof splice and relocating the wire run off the moving hinge. Save $300 that way.
• Gate slams or creeps at the end of travel on swing models. Ghost Controls swing arms use a soft-start/soft-stop that only works when the gate is balanced. If the gate sags even three-quarters of an inch at the latch post, the motor tries to compensate, draws more current, and eventually trips the overload. We level the gate first, sometimes weld a new hinge post plate on site, then run the travel limits. The opener stays. The sag goes.
• Double-gate sync drift on dual-arm installations. On a double swing gate, each leaf has its own arm and control board, and they talk to each other through a sync wire. When that sync wire gets nicked by a weed trimmer or a gopher chews through it under the driveway, one gate opens and the other doesn’t. A lot of companies sell you two new boards. Hal tests the sync circuit first. Most of the time it’s a $40 wire repair, not a $500 board.
• Battery backup that won’t hold a charge. Ghost Controls sells backup battery kits, and in Arcadia’s heat, batteries cook inside the control box if it’s mounted in full western sun. A battery that tests fine on a bench will fail under load after a 105-degree afternoon. We relocate the box to a shaded side of the post or install a ventilated housing. The battery lasts three years instead of one.
• Photoelectric sensor false trips at dusk on the FP series. The sensors work fine until the low sun angles in an Arcadia evening hit the reflector just right and the gate refuses to close. Some brands of sensors are worse for this than others. We’ll swap in a model with a tighter beam pattern and shield the lens. It’s a small parts swap that stops the 7 p.m. callbacks.

Our Ghost Controls Gate Installation Process

Every Ghost Controls job follows the same order, and we don’t skip steps to save a few minutes:

1. 1
   Call and describe the gate. You talk to a person. We ask what the gate is doing, what it sounds like, and whether it ever worked right. We schedule a real window, not a four-hour guessing game.
2. 2
   On-site inspection. We look at the posts, hinges, gate weight, the existing opener if there is one, and the power source. In Arcadia we’re checking whether the post is set in concrete or just dropped in dirt, because that changes everything.
3. 3
   Parts decision, OEM or aftermarket, out loud. If your Ghost Controls board or arm is too far gone, we’ll tell you the price of the factory part versus a quality aftermarket equivalent. We carry both, and we’ll never push the pricier option when the cheaper one will hold up. Warranty implications get explained before you spend a dollar.
4. 4
   The installation. We fabricate brackets and weld on site, not in some shop across town. Your gate stays in your driveway. We mount the opener, run the wiring, set the limits and force settings for this specific gate, not the default out of the box.
5. 5
   Full cycle testing. We cycle the gate a minimum of 20 times open-to-close, watch it under load, and test the safety reverse and sensors. We also leave the area cleaner than we found it.
6. 6
   The 90-Day Done Right Promise, in writing. If anything about the install isn’t right inside 90 days, you call, we come back. No fine print, no arguing.

What Ghost Controls Gate Installation Costs in Arcadia

Every driveway in Arcadia is a little different, but here’s what we typically see:

• Single swing gate, opener only, gate in good shape: $450-$800
• Double swing gate, both arms and sync setup: $850-$1,400
• Slide gate opener with rack install: $900-$1,800
• Full package - new gate plus Ghost Controls opener: $2,800-$6,500
• Battery backup added: $180-$350
• Keypad, wireless intercom, or extra remote programming: $80-$220 per device

What moves the price: whether the existing posts are plumb and solid enough to mount hardware, the gate’s material and weight, how far we have to run wire to your house panel, and whether the gate hinges need welding or rebuilding before the opener goes on. The price gets quoted and you approve it before any work starts. No trip charge inside Los Angeles County, and if you have a written estimate from another company, Hal will give you a free second opinion on it. Call (626) 628-9548 for a free estimate.

Why Arcadia Homeowners Call Gatewood Fence & Gate for Ghost Controls Work

We’re a local, owner-operated shop. Hal Gatewood’s name is on the shop, his address is published, and he’s been working gates in the San Gabriel Valley since 2001. Most of that time he’s called Arcadia home. We service the major automatic gate brands, including LiftMaster, Mighty Mule, and DoorKing, so when a Ghost Controls repair turns out to be better handled with a different opener, we’ll tell you that instead of forcing a square peg. Only if you want it, of course. Every job carries the 90-Day Done Right Promise in writing: if it isn’t done right, we make it right. We weld on site, we answer the phone around the clock with a live person, and the person who shows up at your gate is the same person you’ll see at the Arcadia Farmers Market on a Saturday. We also offer $40 off any repair over $200, no trip charge inside the county, and a standing 10% discount for seniors and veterans. That’s the deal, and it doesn’t change at the door.

FAQs