Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Motor & Opener in Arcadia: What to Know First
FAAC gate motor and opener repair in Arcadia runs $240-$680 for most jobs, and we complete the majority of FAAC repairs the same day. The honest answer on price is that we quote it before any work starts, in writing, and it does not change at the door. If your FAAC gate is stuck, grinding, or refusing to respond to a remote, call (626) 628-9548 and a live person answers.
This page is for FAAC owners in Arcadia who want a straight read on what is wrong and what it costs to fix. Hal Gatewood has worked on FAAC systems throughout the San Gabriel Valley since 2001, and as an independent FAAC service provider, we service the brand without being tied to factory pricing or parts sales. We fix what is broken – not what makes a nice invoice.
How FAAC Products Fail - and How We Fix Them
- FAAC 400 series slide motors losing their limit stops. These units use magnetic limit sensors that drift out of alignment when the gate gets shoved by wind or bumped by a car. The gate then slams at the end of travel or stops a foot short of closed. We realign and reseal the limit housing rather than replacing the board, which is what a replace-first outfit would sell you.
- FAAC 750 and 770 swing operators with stripped nylon drive gears. FAAC builds a sacrificial gear into these swing arms so a hard impact destroys the gear instead of bending the arm itself. That is good engineering. The problem is that once the gear strips, the gate will swing free in one direction and fight you in the other. We keep both OEM and quality aftermarket gears on the van and replace just the gear, not the whole operator.
- FAAC control boards (455D and 455D-EN) killed by Arcadia heat and moisture. These boards sit in a plastic housing that breathes, and the summer heat up against the San Gabriel foothills plus damp winter mornings causes capacitor failure inside the board. The classic symptom is a gate that opens fine in the morning but refuses to respond by late afternoon, or a board that resets when the sprinklers come on. We diagnose the board directly before quoting, because a bad capacitor is a $60 repair where a new board is $600.
- FAAC photocells that mis-fire in strong sunlight. The FAAC photocells mounted low on the gate posts get direct afternoon sun in Arcadia, and the reflectors warp slightly over time. The beam then trips inconsistently – the gate starts to close, reverses, and sits there halfway. Other companies will replace the photocells. We usually find the reflector is the problem and bend the bracket back to true before charging for a new cell.
- FAAC hydraulic operators on older 750 models leaking at the manual release. These are workhorses, but the manual release O-ring hardens with age and heat exposure. You will see a thin film of oil down the side of the operator body and the gate will drift closed over an hour. We replace the O-ring and refill the reservoir, then cycle the gate 20 times with a gauge on it. It beats a $1,800 operator replacement by a wide margin.
Our FAAC Gate Motor & Opener Process
When you call (626) 628-9548 about a FAAC gate in Arcadia, here is how the job actually goes.
- 1
You describe the problem. Tell me what it is doing and I will tell you what it needs – no runaround. A gate that hums but does not move is a capacitor or gear issue. A gate that moves but stops halfway is a limit or photocell issue. We listen carefully because FAAC failures have distinct personalities.
- 2
We arrive, open the panel, and diagnose on-site. Every FAAC job starts with a visual inspection and a voltage check. We do not quote over the phone and then “find more damage” when we show up.
- 3
We give you the price in writing before any work starts. That includes parts and labor, and it is the price you pay. No change orders unless you ask for additional work.
- 4
Parts decision. We tell you when OEM is the right call – usually control boards and safety devices where an aftermarket board will not talk to the rest of the FAAC system. For mechanical parts like gears, pulleys, and limit hardware, quality aftermarket often outperforms OEM for less money. We show you both options.
- 5
The repair. Welding, rewiring, part replacement, whatever the gate needs, we do it in your driveway. We do not haul the gate away. We do not swap parts that still work.
- 6
We test, you test, and we stand behind it. The gate runs through full open-close cycles with you watching. Then the 90-Day Done Right Promise goes in writing. If it acts up within 90 days, one call brings Hal back – no runaround, no second invoice.
What FAAC Gate Motor & Opener Costs in Arcadia
Real numbers, not vague ranges. Here is what we see on FAAC jobs in Arcadia.
- FAAC 400 series limit alignment: $120-$190. Most common FAAC slide gate call we run.
- FAAC 750/770 swing gear replacement: $240-$380 including parts and labor.
- Capacitor replacement on a 455D board: $180-$270. Board replacement, if it comes to that: $540-$720.
- Photocell rebuild or bracket realignment: $140-$220.
- Full FAAC slide motor replacement (400 series): $980-$1,450 installed, depending on gate weight and length.
- Full FAAC swing operator replacement (750/770): $1,200-$1,900 installed, including mounting and settings.
What moves the price: gate weight, travel length, whether the wiring is original or has been hacked up by previous work, and whether we need to weld mounting plates or brackets. We quote the job before we start and the quote holds. No trip charge inside the county, no surprises at the end. Call (626) 628-9548 for a free estimate on your FAAC gate.
Why Arcadia Homeowners Call Gatewood Fence & Gate for FAAC Work
Hal Gatewood has worked on FAAC systems in Arcadia since before half the builders in the foothills started spec’ing them. The name is on the shop, and the shop is down the road – that is the oldest accountability there is. We live about ten minutes from the shop, and if you see a neighbor’s gate acting up, there is a fair chance we already have a service history on it.
Every FAAC job carries the 90-Day Done Right Promise in writing. If it is not done right, we make it right. A live person answers the phone 24/7 – not a voicemail, not a recorded menu, not a call center three states away. And if your FAAC system is truly at the end of its life, we do not twist your arm into a replacement. We will tell you what a comparable LiftMaster, Mighty Mule, Ghost Controls, or DoorKing setup would cost and let you decide. We repair FAAC because FAAC gates are worth repairing.
FAQs
Most FAAC gate motor and opener repairs in Arcadia are completed the same day we arrive. If the part is on the van – and for FAAC 400 limit components, 750/770 gears, capacitors, and photocells it almost always is – the repair is done that visit. If we need a part that is not standard stock, we tell you exactly when it arrives and when we will be back. Call (626) 628-9548 and we will tell you straight what today looks like.
Yes. We are an independent FAAC service provider, not an authorized FAAC dealer. If your FAAC operator is under manufacturer warranty, you have the right to choose who performs the labor, and we do warranty-safe work that does not void your coverage. We will tell you up front before we touch anything whether the repair falls inside or outside the warranty window. Estimates are free.
If the motor itself is burned out or the gearbox is cracked, replacement is usually the better call. If the problem is a limit, capacitor, photocell, gear, or seal, repair is almost always the smarter money – and replacing a whole FAAC operator to fix a $60 capacitor is something we refuse to do. We will show you the failed part and explain what a replacement would cost versus the repair. You decide with real numbers in front of you.
We do. We install new FAAC slide and swing operators for Arcadia homes, including the full setup: motor mounting, limit and photocell alignment, remote programming, and safety edge configuration. We also handle intercom integration and battery backup installs for existing FAAC systems. Pricing is quoted before the job starts and includes the 90-Day Done Right Promise.
The short version: if the gate does nothing when you press the remote and the operator is cold, it is usually the board or the power supply. If the operator hums, buzzes, or gets warm and the gate still does not move, it is usually the capacitor or the motor itself. We confirm with a voltage meter before quoting anything. No guessing, no parts shotgun. Call (626) 628-9548 and describe what the gate is doing – we will tell you what we think it needs before we even roll a truck.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Arcadia and nearby areas.